Odpowiedz do tematu
Odpowiedz do tematu
Zawieszenie C6 allroad
Zna ktoś może procedurę wypuszczenia powietrza z układu zawieszenia w allroad najlepiej przez VCDS? Z góry dziękuję.
Level Control Bleeding/Charging
- Bleeding -
Note: The bleeding procedure will lower the vehicle, proceed with caution and refer to the factory repair manual for proper repair information, warnings and cautions!
Prerequisites:
- System is fault free
- Vehicle is NOT in Jack or Transport mode
- Vehicle is on flat level ground
- Engine running if vehicle is outside or in well ventilated area or use a battery maintainer
If the Security Access code does not work, try Login or Coding-II
[Select]
[34-Level Control]
[Security Access-16], [Login-11] or [Coding-II]
[08367]
[Basic Settings-04]
Enter:
Group 020 = to Bleed Pressure Accumulator
Group 021 = to Bleed Front Axle
Group 022 = to Bleed Rear Axle
Field-4 will display the current pressure
Note: System will time out after 60 seconds, the procedure maybe repeated as necessary to achieve the desired system pressure.
- Charging -
[Select]
[34-Level Control]
[Security Access-16], [Login-11] or [Coding-II]
[08367]
[Do it!]
[Basic Settings-04]
Enter:
Group [023] = to Charge Pressure Accumulator
Group [024] = to Charge Front Axle
Group [025] = to Charge Rear Axle
Field-[4] will display the current pressure
Note: System will time out after 60 seconds, the procedure maybe repeated as necessary to achieve the desired system pressure.
- Bleeding -
Note: The bleeding procedure will lower the vehicle, proceed with caution and refer to the factory repair manual for proper repair information, warnings and cautions!
Prerequisites:
- System is fault free
- Vehicle is NOT in Jack or Transport mode
- Vehicle is on flat level ground
- Engine running if vehicle is outside or in well ventilated area or use a battery maintainer
If the Security Access code does not work, try Login or Coding-II
[Select]
[34-Level Control]
[Security Access-16], [Login-11] or [Coding-II]
[08367]
[Basic Settings-04]
Enter:
Group 020 = to Bleed Pressure Accumulator
Group 021 = to Bleed Front Axle
Group 022 = to Bleed Rear Axle
Field-4 will display the current pressure
Note: System will time out after 60 seconds, the procedure maybe repeated as necessary to achieve the desired system pressure.
- Charging -
[Select]
[34-Level Control]
[Security Access-16], [Login-11] or [Coding-II]
[08367]
[Do it!]
[Basic Settings-04]
Enter:
Group [023] = to Charge Pressure Accumulator
Group [024] = to Charge Front Axle
Group [025] = to Charge Rear Axle
Field-[4] will display the current pressure
Note: System will time out after 60 seconds, the procedure maybe repeated as necessary to achieve the desired system pressure.
Odpowiedz do tematu
Nie możesz pisać nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów
Nie możesz głosować w ankietach
Nie możesz załączać plików na tym forum
Możesz ściągać załączniki na tym forum
Dodaj temat do Ulubionych
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów
Nie możesz głosować w ankietach
Nie możesz załączać plików na tym forum
Możesz ściągać załączniki na tym forum
Dodaj temat do Ulubionych